The global configuration command ip default-gateway 172.16.100.1 is applied to a switch. what is the effect of this command?

While trying to solve a network issue, a technician made multiple changes to the current router configuration file. The changes did not solve the problem and were not saved. What action can the technician take to discard the changes and work with the file in NVRAM ? Close and reopen the terminal emulation software. Delete the vlan.dat file and reboot the device. Issue the reload command without saving the running configuration. Issue the copy startup-config running-config command. After making configuration changes on a Cisco switch, a network administrator issues a copy running-config startup-config command. What is the result of issuing this command ? The new configuration will be stored in flash memory. The new configuration will be loaded if the switch is restarted. The current IOS file will be replaced with the newly configured file. The configuration changes will be removed and the original configuration will be restored. What are two characteristics of RAM on a Cisco device? (Choose two.) The contents of RAM are lost during a power cycle. RAM is able to store multiple versions of IOS and configuration files. The configuration that is actively running on the device is stored in RAM. RAM provides nonvolatile storage. RAM is a component in Cisco switches but not in Cisco routers. What function does pressing the Tab key have when entering a command in IOS? It exits configuration mode and returns to user EXEC mode. It completes the remainder of a partially typed word in ...

Hi I saw the following: " ------------------ Use the following commands to assign the IP address 192.168.1.254 to VLAN 1, which is the management VLAN by default: TEswitch1(config)#interface vlan 1 TEswitch1(config-if)#ip address 192.168.0.9 255.255.255.0 TEswitch1(config-if)#no shutdown If you need to be able to connect to the switch from other networks, you will also need to configure a default gateway address. For example, if the switch is connected to a router with the IP address 192.168.1.254, use the following command, in Global Configuration mode, to use it as the default gateway: TEswitch1(config-if)#exit TEswitch1(config)#ip default-gateway 192.168.0.254 ------------------------ " My question is why we still need to use command ip default-gateway since the router still can reach the switch from other network without the ip default-gateway. Thank you My question is why we still need to use command ip default-gateway since the router still can reach the switch from other network without the ip default-gateway. If you don't add the ip default-command to the switch, the switch can only reach hosts in the local subnet (192.168.0.0/24) and no other subnet. Also without this command, no other device outside subnet 192.168.0.0/24 can reach this switch. HTH Thank you so much for your reply. Here are two cases: One is switch(192.168.0.9/24(vlan1) -------------(192.168.0.1/24)Router 1 Two is Router2(192.168.0.9/24) -------------------(192.168.0.1/24)Router 1 I think the comm...

• • • • Question:46 What are three commonly followed standards for constructing and installing cabling? (Choose three.) pinouts tensile strength of plastic insulator cost per meter (foot) cable lengths connector types connector color 47 Which two functions are performed at the LLC sublayer of the OSI Data Link Layer to facilitate Ethernet communication? (Choose two.) O 46 What are three commonly followed standards for constructing and installing cabling? (Choose three.) pinouts tensile strength of plastic insulator cost per meter (foot) cable lengths connector types connector color 47 Which two functions are performed at the LLC sublayer of the OSI Data Link Layer to facilitate Ethernet communication? (Choose two.) O integrates Layer 2 flows between 10 Gigabit Ethernet over fiber and 1 Gigabit Ethernet over copper implements trailer with frame check sequence for error detection enables IPv4 and IPv6 to utilize the same physical medium places information in the Ethernet frame that identifies which network layer protocol is being encapsulated by the frame O applies source and destination MAC addresses to Ethernet frame 48 What two pieces of information are displayed in the output of the show ip interface brief command? (Choose two.) O speed and duplex settings O next-hop addresses O IP addresses O MAC addresses O interface descriptions O Layer 1 statuses 49 A group of Windows PCs in a new subnet has been added to an Ethernet network. When testing the connectivity, a technici...

Question: The global configuration command ip default-gateway 172.16.100.1 is applied to a switch. What is the effect of this command? • The switch will have a management interface with the address 172.16.100.1. • The switch can be remotely managed from a host on another network. • The switch can communicate with other hosts on the 172.16.100.0 network. • The switch is limited to sending and receiving frames to and from the gateway 172.16.100.1. Explanation: A default gateway address is typically configured on all devices to allow them to communicate beyond just their local network.In a switch this is achieved using the command ip default-gateway . Exam with this question: Exam with this question: Exam with this question: Exam with this question: Exam with this question: Post navigation